Reflash your 2002-2004 RSX MT (K20A3 engine) engine computer.
- Fuel, ignition timing and cam timing optimized.
- Rev limier optionally increased to 7300 rpm
- 5-10 HP increase across most of the rev range.
- 10-12 ft/lb torque increase under 5000 rpm
- More torque than a stock K20A2 Type S under 6300 rpm. (see dyno graph)
- No measurable difference in emissions from stock.
- Fully dealer compatible - works with all Honda scan tools and equipment.
Hondata does not sell direct - all sales and payment must be conducted through Hondata dealers. The ECU reflash form must be sent with your ECU.
Applications
- K20A3-M1: Revised fuel and ignition values with stock rev limit
- K20A3-M2: Revised fuel and ignition values with 7300 rpm rev limit
Both these reflashes are based on the performance program in the dyno chart below and vary only by rev limit. VTEC point is not altered.
We do not recommend the use of this reflash with nitrous or forced induction. For these applications we recommend the K-Pro.
Warning
Within the USA this product is legal only for racing vehicles which may never be used upon a public highway.
Specification
| Restriction | |
| EPA/CARB status (USA) | Competition vehicles only |
| Vehicle | |
| Model | RSX |
| Year | 2002-2004 |
| Market | US |
| Trim | Base |
| Engine | K20A3 |
| Transmission | MT |
| ECU | |
| Part Number | 37820-PND-A01 to 37820-PBD-A09 |
This test RSX base model had 28,000 miles at the time of testing. Intake and exhaust were stock. The fuel used was 89 octane - but we recommend 91. We cannot turn your base model into a Type S (please read K series Tech), but we can make significant improvements.
K20A3 RSX base model Stock vs Program
More torque than a stock Type S!
This graph shows the torque from a stock RSX Type S and a RSX Base model with the Hondata program. The Type S had only about 1500 miles and would show more torque after a few thousand more miles.
Comparisons to a cold air intake
Long cold air intakes work the best. The long cold air intake we tested with added 5-6 ft lb across the rev range from 2800 rpm up. By comparison the CAI makes more top end power from about 5500 rpm and up Hondata program makes significantly more torque under 5500 rpm. This graph shows only the CAI with no Hondata program.
In this graph we test the CAI and Hondata program together.
Tech
VTEC
These engines have a VTEC point of 2200 RPM. Under this rpm the K20A3 operates as a 12 valve engine. Hondata does not change this. See K series Tech for more info.
For consistency in dyno testing we suggest you follow the dyno procedure outlined here.
Immobilizer
The immobilizer feature on the US Spec RSX is the most advanced to date. The ignition key, the immobilizer box and the ECU are all matched. It there is not a match there will be no fuel or spark. Japanese ECUs have less protection and are more easily bypassed.
The K series ECU, in order to be re-programmed must have a functioning immobilizer system. Three items must be sent to Hondata: the ECU, the ignition key and the immobilizer. The immobilizer works as normal after the ECU has been re-flashed.
Tools needed:
- Philips screwdriver
- 10 mm socket and drive
- Time needed : 10-15 minutes
Removing the immobilizer (Civic Si, RSX / Integra)
Under the steering column remove the three philips screw holding on the bottom plastic cover.
Depress the bottom cover along its top edge where it meets the top cover to separate the plastic clips. Rotating the steering wheel 45 degrees can help.
Lower the steering column and remove the bottom plastic cover from over the height adjustment lever.
Unclip the green connector immobilizer connector and unscrew the securing two philips screws.
Recently viewed...
-
$295.00